Small metal object with clip on top. Clip spins around the object body and can be attracted to a magnet (so made of steel probably). Object body does not react to magnet (so made of brass maybe). Cone shaped tip seems to be made of some kind of plastic....
Looks a lot like a carburetor float needle to me. It allows the flow of gasoline into the float bowl, which sets the amount of fuel fed into the engine.
It’s common for float needles (and carb parts in general) to be made of brass, and the wire clip being made out of steel is also consistent with a float needle. The plastic tip is probably used for a better seal when the float is up, closing the needle port.
I finally got a filament drying box and I’m using it prior to and during prints. It seems to be helping. I’m a bit of a color queen, so I keep a pretty big backlog of different filaments. I’ve been storing them in vacuum bags but the vacuum bags often seem to lose some of their vacuum after a few months; the whole process...
I wouldn’t bother with vacuum bags If I were you. I think it’s fine if you’re using a drying box after the filament has been sitting out a while. Doesn’t hurt to try and find out at least…
Personally, I just use a big plastic storage bin with a bunch of silica desiccant in it. I just busted out some polycarbonate (notoriously hydrophyllic) recently that had been sitting in there for 4+ months and printed straight away; no stringing or anything.
My prints get very good adhesion to the bed, especially when doing prints with large adhesion areas. So good, that after the print is done, I actually have to wet the surface with alcohol and put it in the freezer for it to let go! (edit: I print with PLA)...
I use the washable gluesticks for my polycarbonate prints. I just put PC prints under warm water for a few minutes and they pop right off. Gluesticks generally reduce bed adhesion though IME, so it’s a fine line to walk; I never use gluesticks with PETG for example because then the parts don’t stick to the bed enough.
Hi guys, do you know if there is a good RSS Feed service that can be self-hosted which also exposes a good front-end to read the subscribed news? Thanks in advance.
I’m sur a lot of you have seen this video from James Hoffmann discussing the massive differences observed when spritzing some water on the beans before grinding....
Yup, as a software dev, I would love to be able to devote all my time to writing open source, but I gotta make money to live as well. Switching to working on OSS would be a huge leap of faith that there is someone out there willing pay/donate for my work. As it is, I think it will be my way of giving back once I have saved up enough money from my proprietary work, and hopefully I will be able to switch over sooner rather than later.
Maybe I’ll go take a look at what the process is for getting grants from the government or non-profit orgs like Apache foundation…
Yup, that’s true, and I am always open to and looking for new opportunities, but that also requires them to be interested in hiring me - not a trivial feat, especially in the current job market.
I’d also wager that the number of job positions writing OSS for organizations like that is much lower than proprietary job positions.
But you know what, I’ll go shop around a little in my free time the next week or two. I’d love for (more of) my work to be publicly accessible and not locked up in a proprietary codebase.
Very small valve part? (lemmy.world)
Small metal object with clip on top. Clip spins around the object body and can be attracted to a magnet (so made of steel probably). Object body does not react to magnet (so made of brass maybe). Cone shaped tip seems to be made of some kind of plastic....
Are filament vacuum bags worthwhile?
I finally got a filament drying box and I’m using it prior to and during prints. It seems to be helping. I’m a bit of a color queen, so I keep a pretty big backlog of different filaments. I’ve been storing them in vacuum bags but the vacuum bags often seem to lose some of their vacuum after a few months; the whole process...
Can too good adhesion be countered by lower bed temps?
My prints get very good adhesion to the bed, especially when doing prints with large adhesion areas. So good, that after the print is done, I actually have to wet the surface with alcohol and put it in the freezer for it to let go! (edit: I print with PLA)...
5 February 2024 (sh.itjust.works)
[Resolved - now using Onboard] Any recommendations for an on-screen keyboard like the one that Windows has. The one that comes with Gnome is annoying to use... (lemmy.world)
It pops up and down from the bottom of the screen when I don’t want it to
Any good RSS Feed service for self-hosting?
Hi guys, do you know if there is a good RSS Feed service that can be self-hosted which also exposes a good front-end to read the subscribed news? Thanks in advance.
Water spritz method for espresso
I’m sur a lot of you have seen this video from James Hoffmann discussing the massive differences observed when spritzing some water on the beans before grinding....
When "I fits, I sits" goes too far (lemmy.world)
(Disclaimer: not my cat, not my picture, found in an imgur dump)
Unity backtracks slightly on plans to charge developers for game installs (www.eurogamer.net)
Game development engine Unity has U-turned on some parts of its hugely controversial plan to enforce fees on game creat…
Imagine (sh.itjust.works)