Extelec, 2 months ago Loads of work to do today... PCBs arrive <distracted by asquirrel mode> Must build pcbs... :)
Loads of work to do today...
PCBs arrive
<distracted by asquirrel mode>
Must build pcbs... :)
Extelec, 2 months ago Well all the important bits ate on, let's see if it works.
Well all the important bits ate on, let's see if it works.
Extelec, 2 months ago Slight delay, It doesn't work, It's an error when populating the PCB , plainly seen in the last photo... 10 internet points and a google free cookie, if anyone can spot the "small" error.
Slight delay, It doesn't work, It's an error when populating the PCB , plainly seen in the last photo...
10 internet points and a google free cookie, if anyone can spot the "small" error.
jerry507, 2 months ago @Extelec Gpio16 doesn’t usually route to pin 1?
@Extelec Gpio16 doesn’t usually route to pin 1?
Extelec, 2 months ago @jerry507 You win the Cookie and the internet for the day :)
@jerry507 You win the Cookie and the internet for the day :)
jerry507, 2 months ago @Extelec woohoo! And ☹️ for you having to desolder all those castellated pins!
@Extelec woohoo! And ☹️ for you having to desolder all those castellated pins!
thejpster, 2 months ago @Extelec the only excuse for an upside down Pi is when you want to avoid touching the chips with the foil tray the Pi comes in.
@Extelec the only excuse for an upside down Pi is when you want to avoid touching the chips with the foil tray the Pi comes in.
Extelec, 2 months ago @thejpster @semachthemonkey Personally I blame @Raspberry_Pi Every 100 or so Picos, they make one upside down... What a pain :)
@thejpster @semachthemonkey
Personally I blame @Raspberry_Pi
Every 100 or so Picos, they make one upside down...
What a pain :)
semachthemonkey, 2 months ago @Extelec @thejpster @Raspberry_Pi You should have just used a mirror to reverse everything. I know all the silkscreen would be harder to read, but it is easier than desoldering the Pico!
@Extelec @thejpster @Raspberry_Pi You should have just used a mirror to reverse everything. I know all the silkscreen would be harder to read, but it is easier than desoldering the Pico!
Extelec, 2 months ago @semachthemonkey @thejpster @Raspberry_Pi Which would have worked apart from physics and reality.
@semachthemonkey @thejpster @Raspberry_Pi Which would have worked apart from physics and reality.
LewisWorkshop, 2 months ago @Extelec "always buy three... One to fit backwards, one to drop on the floor and lose, and one to fit correctly."
@Extelec "always buy three... One to fit backwards, one to drop on the floor and lose, and one to fit correctly."
Extelec, 2 months ago @LewisWorkshop I do, and this is why I'm running out of space with a loft full of 1-2 of everything.
@LewisWorkshop I do, and this is why I'm running out of space with a loft full of 1-2 of everything.
Extelec, 2 months ago OK, my slight error was the pico was upside down. I got this far before realising I'd pulled off some pads on the pcb.
OK, my slight error was the pico was upside down.
I got this far before realising I'd pulled off some pads on the pcb.
Extelec, 2 months ago (edited 2 months ago) But one pico and another PCB later It works *first time. *Because re-soldering the whole PCB again and using a new pico still counts as first time as I hadn't put power on the board. Doesn't it ?
But one pico and another PCB later
It works *first time.
*Because re-soldering the whole PCB again and using a new pico still counts as first time as I hadn't put power on the board.
Doesn't it ?
Ryanteck, 2 months ago @Extelec I would say it still counts as first time, it's not another PCB revision so it counts!
@Extelec I would say it still counts as first time, it's not another PCB revision so it counts!
Extelec, 2 months ago @Ryanteck Vindicated :)
@Ryanteck Vindicated :)
Add comment