Hello all. I am very new to this but it is all very cool to me. I ran into a problem and I am not sure how to troubleshoot it. I downloaded a simple pull string helicopter off thingiverse. After running through the slicer software, the estimated build time is 131 hours. Relative to it’s size this seems insane. If I “run the...
In other news, if you try to upload a file named uncalibrated_example.stl to Thingiverse, it fails with no error message, because somewhere they have a pr0n filter searching for rated*x....
This is a fully 3D printable clamped under desk drawer. What makes this drawer different? Well, Because it's clamped, you don't need to ruin the bottom of your desk with screw holes!
I designed this wonky-looking funnel to fit my Squirrel Buster Legacy (and probably similar models), with hooks and posts that make it possible to refill the feeder without setting any parts on the ground....
På arbejde har jeg adgang til en Ultimaker S3. Den bliver brugt for lidt, og jeg søger inspiration… Forleden faldt jeg så over en Duplo-Brio-adapter på Thingiverse, jeg vil printe til min datter.
Alright this project is growing.. needs a new description. I recommend printing the drawers laying bottom down with tree supports, or on their back. Either way should work, but bottom down will use less support material. To free the pins in the back after printing, place your fingers behind the pin and give it a few sharp taps...
This a remix of trentesous' very good foldable tripod Version 2. I remade the phone mount to rotate, allowing for both landscape and portrait modes. Find the original here: https://www.thingiverse.com/thing:2862445 Printing tips: Make sure to enable supports but use support blockers for the threaded bits The orientation of the...
Parts for cable management under a desk. They are screwed to the desk and use tie wraps to fasten the cables. Added 4,5 and 6 Cable holders. Added Samsung Portable T7 SSD Drvive Holder Added regular SSD Drive Holder
USB-Cable-Holder for Ikea Skadis Wall. Standalone with little top Tray or for using as Addon for: https://www.thingiverse.com/thing:6320736 [works as addon only with the horizontal one obviously] Technical Data: i've only tested this with a cable length of 1m rolled cable should have a diameter between 50-60mm Print Settings...
I posted here a bit ago with zero 3d printing experience. You guys helped me mash this case together. I printed it, attached it to my phone, and it seems to work. It has a magnetic ring that I bought from quadlock, but it fits in the case, so it effective has both quadlock and magsafe capabilities. I reinforced the attachment...
Universal holder for any cordless drills and tools. I used it mainly for Makita, but other power tools should fit as well of course. The following Makita tools have been tested so far in the 40mm version: Makita DTD171 Makita DDF484 Makita DDF484B Makita DHP484 Makita DDF459 Makita DHP481 Makita DTW300 Makita DTW302 Makita...
Whipped up this quick wall mounted spool holder. made to accommodate 1.1kg spools and under at 100% scale and should accommodate 3kgs by just upscaling. feel free to remix and repost all I ask for is oc credit.
Update 2023-11-27: This thing is Version 1 of my adaper. I have now designed Version 2, with the following improvements: the smartphone's center of gravity is now directly above the mounting screw, which gives the tripod a more secure stand, The tripod adapter is now even more compact and lighter. You can download this new...
The folks in 3d printing helped me out greatly with this, and I was able to mash this together today. I haven’t printed or tested it yet, but it’s designed to be used with the quad mag ring. I’m going to use some very thin and strong 3m adhesive tape I have to ensure it is secure to the phone, and use for a quadlock mount...
This is a fully re-modeled build of a MicroSD case inspired by Kozalakis's one, borrowing some ideas from Kroki's remix of it. I didn't actually use any of their source, rather building from scratch using SD/MicroSD card dimensions. This version relies on fairly close tolerances, so it may be a bit temperamental on some 3D...
This is a strong corner for fixing three planes. Print as in the screenshot. Added a new v2.1 version! The area of contact with the planes has been increased by adding small overhangs that do not affect the print quality. Added a new v2 version! Removed overhangs for simpler print quality. Increased base area for better...
Similar tools are sold online, pretending to help creating friendship bracelets. I was curious, so I created one for my daughter. Even not really needed it helps to keep the right order of the strings, which helps the younger ones... You should still attach the initial end of the strings somewhere so you can give some tension on...
It helps categorise, manage, and present content effectively, commonly found in applications. About 130mm in width x 30mm in height. An add-on is an optional component, feature, or extension that can be integrated into an existing system. More designs on Printables: https://www.printables.com/@ChrisTech Change Log: 7 November...
Find out everything you need to know about the battery box on my blog: https://nerd-corner.com/3d-printed-battery-container-for-cr2032/ or https://nerd-corner.com/de/3d-gedruckter-batteriebehaelter-fuer-cr2032/
Redesign of a simple micro SD card organizer, based on the original MicroSD Card holder by FritoBandito. Created a new model in Autodesk Fusion 360. Redesigned the slots for easier card removal. Print with 0.2mm layer height
This is a wall mount I designed and made for the Meta Quest 3 VR Headset; I also made a wall mounts for the Quest 1 and 2 when they were released, (see other designs) and was hoping to have this wall mount compatible with the Quest 1 and 2, but the design of the Quest 3 prohibits that. I have added three new STL files to make...