prompted by poopbag holder (lemmy.world)
Just a simple 2 part print to protect the bag when out and about. Snap fit top
Just a simple 2 part print to protect the bag when out and about. Snap fit top
cross-posted from: slrpnk.net/post/9706069...
printables.com/…/885862-pellet-press-funnel-for-d…...
cross-posted from: lemm.ee/post/31379850...
One of the best things about 3d printing is fixing problems that you and 2 other people have. This box dries the filament I use and the opening strap snapped off within a week. Someone made a knob. 10 min print. Bam. Works again....
I wanted a shelf to hold the EIBOS 3D Series X or whatever on top of my SV06 Plus. It’s not a great dryer, I don’t recommend it, but it’s what I have. It works… kinda....
cross-posted from: lemm.ee/post/27620066...
cross-posted from: lemm.ee/post/27376719...
With the talk of Erenst (The solo guy running kbin) missing in action, there's talk of communities migrating over to other instances that are maintained by more than 1 person....
With the talk of Erenst (The solo guy running kbin) missing in action, there's talk of communities migrating over to other instances that are maintained by more than 1 person....
I have previously duplicated the Milwaukee Low-Profile Organizer bins, (as well as designed modified ones) and the regular height organizer bins and posted them on Printables and Thingiverse, and I was asked to design printable bins for the new deep organizer....
This is a fully 3D printable clamped under desk drawer. What makes this drawer different? Well, Because it's clamped, you don't need to ruin the bottom of your desk with screw holes!
cross-posted from: thelemmy.club/post/9213590...
cross-posted from: ttrpg.network/post/4222671...
All the sanding blocks I have seen are the nut and bolt type, but i found myself wanting something more of just a … block. No adjusting, loosening, tightening, moving, just wrap your sandpaper around an edge and go. So I spent 15 minutes in FreeCAD and made one. So far it’s working great....
Alright this project is growing.. needs a new description. I recommend printing the drawers laying bottom down with tree supports, or on their back. Either way should work, but bottom down will use less support material. To free the pins in the back after printing, place your fingers behind the pin and give it a few sharp taps...
This a remix of trentesous' very good foldable tripod Version 2. I remade the phone mount to rotate, allowing for both landscape and portrait modes. Find the original here: https://www.thingiverse.com/thing:2862445 Printing tips: Make sure to enable supports but use support blockers for the threaded bits The orientation of the...
Parts for cable management under a desk. They are screwed to the desk and use tie wraps to fasten the cables. Added 4,5 and 6 Cable holders. Added Samsung Portable T7 SSD Drvive Holder Added regular SSD Drive Holder
I have a few Anker 313 wireless charging stands around the house. They work great with iPhones. Due to the design, they can’t charge an AirPods case without an adapter to lift the case to the right spot. That is the purpose of this model. I don’t have the old style non-Pro AirPods, but this will probably also work with that...
I own a pellet stove that has a heat exchanger with extra long cast iron “fingers” (see photo). This needs to be cleaned regularly. The challenge is, a standard brush attachment’s bristles are too short to do this properly. This vacuum attachment solves that problem. It fits a Loveless ash vacuum but should also fit other...
USB-Cable-Holder for Ikea Skadis Wall. Standalone with little top Tray or for using as Addon for: https://www.thingiverse.com/thing:6320736 [works as addon only with the horizontal one obviously] Technical Data: i've only tested this with a cable length of 1m rolled cable should have a diameter between 50-60mm Print Settings...