I spilt coffee all over my keyboard this morning and it’s all sticky, since it didn’t break can I just pour water on it to help the stickiness?
I know that sounds like a stupid ass question. I have the Logitech wireless mx keys. I wiped the keyboard down so the surface of the keys aren’t sticky, just hard to press down and some have a spasm.
Since a whole ass thing of coffee did not short it, it gives some credibility that it is water resistant. Can I just dump water on it to help it?
First of all I believe your keyboard has a built in lithium ion battery. If this is the case, DO NOT introduce any liquids (or heat) unless you have physically removed the battery.
There are people claiming you can rinse keyboards, or even use a dishwasher (lowest temperature, remove before drying cycle) either after separating the electronics from the rest of the keyboard or even without that.
Water itself doesn't kill electronics, corrosion and power getting to the wrong spot do. Corrosion happens really quickly if power is applied while wet, and obviously wet + power can apply power where it shouldn't. So whatever you do, make sure all power - including internal batteries - are removed until completely dry. That means days.
Isopropyl alcohol evaporates more quickly, which is why it's sometimes recommend. However, it's also a solvent and can attack some plastics. It is fine for cleaning most PCBs ("circuit boards"). IPA is highly flammable. See the warning about batteries above.
Well if you take out the batteries, probably you could - but I think it's best to just strip it down and I washed mine in the bathroom sink with a bit of detergent (dish soap), then dry it before re-assembling it (I did this with my ancient Logitech K270 keyboard a few times).
The main issue with spills is that they dry sticky, and then the keys will get sticky - so you need to dump out the keys and wash them. On my keyboard, they just pop out and clip straight back in again.
when I was a kid, I added too much salt to my scrambled eggs, I tried to counter its effect by adding sugar. needless to say, it didn't work as I expected.
what type of keyboard? Are the switches mechanical?
If they are you can pull all the key caps, and switches. Then use a microfiber cloth with 70% isopropyl alcohol to clean the PCB and case.
You can run the caps through your dishwasher inside a basket so they dont go flying just wash without heated water and heated dry.
For the switches it depends, generally you will need to open them up and clean them with isoprobyl and then re-lubricate before installing them back in.
If this is a cheap rubber dome keyboard, toss it and get a better one with hot swap keys that you can repair in the future.
I had an extremely grungy keyboard, lots of crumbs, hair, food, etc. I set it out in the driveway and cleaned it with a pressure washer. It was sparkly when I was done. Let it dry in the sun for a day and it was fully functional.
I've heard of people cleaning then in the top rack of a dishwasher as well. Not sure I'd try either of these with a really high-end keyboard, but ymmv.
I just rescued a keyboard from a ramen spill over the weekend. There are a few things you can do to make it a bit safer and more reliable than "just dump water on it."
Power off immediately (incl battery).
Disassemble as much as you're comfortable -- removing the keycaps is a must, opening the case is optional -- and use DISTILLED water on any part that may have been coffee'd. Don't apply pressure or scrub - pour directly onto the components (gravity is your washing pressure) with a tub underneath, then swish the components around in the tub.
Let dry for a day or so, then come back with isopropyl alcohol (at least 95%), cotton swabs, and compressed air. Put your keycaps back in and test each one -- any that are still sticky get taken back off, then get a good swab full of alcohol down in the switch or membrane. Use the compressed air to help blow it down in there + assist the drying process.
Let dry for another day or two (until completely dry) before attempting to power back on.
The whole point in using 95% or 99% isopropyl for cleaning electronics is that less water and other potentially conductive impurities get left behind when it dries. Yes 70% is better for general purpose cleaning and it will work on electronics in a pinch but when working with electronics you ideally want the highest concentration isopropyl alcohol that you can get.
I work for a company that manufactures electronics and all of our general product cleaning is done with 99% isopropyl. We will also clean some product with water but that uses highly filtered deionized water and what basically amounts to a fancy dishwasher with a conveyor running through it. That's also only really done when water soluble fluxes are used, otherwise it's just the alcohol for cleaning.
Turn it off, REMOVE THE BATTERY (important step, batteries are dangerous and do not like liquids), then disassemble it. Remove the keycaps and rubber membrane and wash them with soapy water, and wipe down the gold contacts with isopropyl alchahol. Wait for it to dry completely before reassembling it.
I did this years ago with a $400 keyboard. In short, it was sticky for a day, then every morning for a few days the keys were stuck in the 'up' position. I just encouraged them to get unstuck and it would work fine until the next morning. After a few days it was fine.
Funny story, I spilt coke all over my first mechanical keyboard. I tried everything to fix it, water, rice, alcohol. After all that it still felt horrible so I ended up just buying a new one. But I didn't throw it away, I just stuck it in my closet where it remained for years.
Then approximately 8 years later, I take it out, randomly decide to try typing on it.. its perfect. Felt just like it did when it was new, I dunno if the sugar just broke down or degraded over time or what, but it was fixed.
So if nothing else, just put it into storage for a decade and then try it out again lol.
Did a quick search and it looks like it uses Kalih Choc V2 mechanical switches. The each key cap should be held on to the switch by a friction fit. You should be able to pull each key cap off then soak them in some soapy water. If you don't have a key cap puller, you can try using some string and a pencil or wooden dowel to make a cheap one.
Although from what you described, coffee may have gotten into some of the switches. That would require replacing the sticky switches or taking them apart, cleaning, and re-lubing them. In either case, pulling the key caps will give you a better idea of where all the fluid ended up.
Some people have recommended alcohol. If that gets into the switch it will dissolve the lubricant.
I would say pull a couple keys you care the least about then take a closer look before you decide how you want to tackle cleaning it.
That's a scissor switch which you have to tackle a different way. So disregard most of what I've said. Coffee residue is likely gunking up the plastic switches. You can try to find a guide to take those apart, but they can be a little more delicate.
ifixit has a couple guides for how to take the keyboard apart. That will let you separate the electronics from the switch assembly.
I got something (coffee, or possibly a bit of soda) in my mx (exact same model) and I just spritzed it out with 98% isopropyl and let it air dry. Now about 70% of the backlight doesn’t work. Kind of a fail, really.
Add comment